The 1971 Boss 351 replaced the previous Bosses and became known as the performance Mustang. There were 1,806 of these special cars made. They came with very few options, including:
- Boss engine,
- ram air,
- 3.91 rear axle,
- traction-loc,
- 4 speed manual transmission,
- competition suspension,
- Front power disc brakes
- Front spoiler,
- Mach 1 front grill
- Mach 1 lower body side paint
- 351 decals and tape treatment,
- Chrome front bumper
- Hood that was mostly blacked out.
- 15×7 wheels and chrome trim rings
- Goodyear F60x15 RWL tires
The original Boss of 1969-70, the Boss 302, was a homologation model, produced to meet the eligibility requirements of the SCCA Trans-Am series. It used a high-revving 302-cid V-8 rated at 290 horsepower, built to meet the race series’ five-liter class limit.
Ford, however, had ended its Trans-Am program by the time the bigger, heavier Boss 351 arrived late in the 1971 model year. Though it lacked a racing pedigree, the new Boss turned out to be one of the fastest Mustangs of the day. It was also one of the rarest, with just 1,806 built.
“The Boss 351 was more drag-racing oriented than the Boss 302, but better handling than the 429 Cobra Jet,” said Mike Berardi, global director of service engineering operations at Ford Motor. A red Boss 351 is one of 55 Mustangs in his collection, and a favorite to drive. “It’s high revving, so you row the gears more than with a 429 CJ,” he said.
The 351 in the ’71 Boss was Ford’s 351-cid Cleveland engine, nicknamed for the Ohio plant that built it. The 351C shared little more than bore and stroke spacing dimensions with the 351 Windsor used in the 1969 Mustang. Its advantage was deeper breathing, a result of huge ports and valves in the cylinder heads. The 1969-70 Boss 302 had married the Windsor block with Cleveland heads, but the Boss 351 was the whole deal, with lots more torque.
Starting with the 11:1-compression 351C with four-barrel carburetor, Ford assembled a hot rodder’s wish list: four-bolt mains; forged pistons; shot-peened connecting rods; high-lift camshaft; aluminum intake with 750-cfm carburetor; dual-point ignition and ram air induction. It added up to 330 horsepower at 5,400 rpm and 370 pound-feet of torque at 4,000 rpm, matching Chevy’s LT-1 350 in the 1971 Camaro Z28. Magazines that tested the Boss 351 posted quarter-mile times in the low-14-second range at about 100 mph, on par with big-block models like the Mustang 429 CJ.
Download the 1971 BOSS 351 Brochure
Current Forum Topics
- 1972 Mustang Coupe 302Just purchased a 1972 302 V8 coupe as a project. Picked it up in CA from a vet who had it in his garage, barring the occasional grocery run. The car runs incredibly well, the interior is in great shape and I finally snagged it after years of wanting one. There is some body work […]
- Rear quartersI am looking for help , I am almost ready for paint on my 1971 coupe , have it primed and wet sanded ( for the most part ) and did not realize that the aftermarket quarters came with holes for 1973 only Rear bumper, fillers Don t know best way to loose them at […]
- New to the Group!Happy to join this group. I found and purshased a great '72 Coupe that already had a completely restored engine and drive train. The exterior body work was almost complete as well. So I've been focusing on restoring the interior with new OEM parts where available but I've wasted some time and money on a […]
- What is the best rear axle ratio for our cars?I was just replying to a thread from jscott about a noise he is hearing that sounds just like the noise I am starting to hear. It seems the general consensus in that thread is that it is probably the differential failing, which I expected from my car but was trying to get the rest […]
- 1973 Convertible Project: Undercoating Decision TimeWell, I guess I did it. I got a second 73 Project car. Now, while my 73 Coupe (Grande) looked like a basket case (BC) project when I got it, I might have just found one that is one basket short of a BC. Ok, the Pros and Cons: PROs Looks like it was a […]
- SubwooferLooking at putting a powered subwoofer in my 1973 coupe. Considering the type that sits under a seat, but not sure any will fit. If I put it in the trunk, how will the sound deadener I have installed affect the sound? Anybody else go this route?
- Strange noiseOn my way home yesterday, after driving the car for 2+ hours I started to hear a noise. It sounded like if you were driving past a saw mill, a high speed metal noise that would come and go. When I would take my foot off the gas it would stop immediately, Revving the engine […]
- NOS 71-73 Pop open gas cap D1ZZ-9030-C MotorcraftNOS original Ford pop open gas cap. It is a D1ZZ part number but the cap is a D2zxxx Motorcraft. Perfect for a 72 HO R code Mach 1. Please see condition and ID in pictures. Shipping from 80136. Local pick up ok. Starting to dig into the mess. $300 obo A joke: Why did […]
- Frankenstein Mach 1 in VegasFinally got this new to me Mach 1 running well enough to drive around the block so I figured its time to start a build thread! You can view my intro post here: https://7173mustangs.com/threads/new-member-just-purchased-71-mach-1.45749/ And the issues I have been having with the engine so far here: https://7173mustangs.com/threads/351c-where-to-start.45750/ Here are the cliff notes: I purchased […]
- Nevermind I got this figured out with the stripes for the Mach 1Thanks to everyone that helped me.
- Power Steering on1969 Shelby leaks from filler tubeWhy would a (like new) power steering pump on a 1969 351 push fluid out the filler tube. It's not over filled and I replaced the dipstick in case that was it. The car also steers hard when the car is barely moving, but steers fine when driving down the road. I don't mind replacing […]
- What did you do today instead of working on your Mustang?For me I am waiting on the 71/72 weld / sealant book to show up. No book = no seam sealer going on the car yet. So instead of working on the Mustang I decided to work on my daily driver project instead. Master cylinder was leaking on the diesel 83' GMC 4x4. In the process of […]
- Rear main seal on 1969 351 windsorAny suggestions on replacing the Rear main seal on 1969 351 windsor without pulling the crankshaft. The 1/2 of the seal between the block & crank shaft is what I'm looking for suggestions on. I'm replacing the oil pan gasket (one piece) with the motor in the car.
- Duraspark II with ram air debacleMy new to me 71 Mach 1 with 351c has a mish-mash of parts that I am trying to sort out. At some point a Duraspark was installed on this vehicle (best guess is out of a 74 Gran Torino along with the engine.) I was having running issues with the engine so I wanted […]
- New regulator and ps dipstickI have these leftover parts from my build Just pay $10 shipping or pick up near Dallas, Tx. Thx all.